AC Control
Part Number
Model 30510-01, AC control module with integral ground fault isolator, two AC outlet plugs, rated at 20 Amps (total load), 45 Amp electronic switch with optoisolated control inputs (5-24 VDC control input). Bypass switch allows local control. Status indicator to show on/off condition. Interfaces directly to MCU500 digital outputs. Switch can be fitted wtih safety guard to prevent accidental tripping or leaving the switch in the wrong position. Can be mounted to panel board or post using external mounting tabs.
Same as above, but without the GFI: 200-30510-02
3 phase contactor, for motor control. 15 Amp, 240 VAC, with local/off/remote switch. Designed for interface to an MCU digital output channel for direct control of motors, etc..
AC sensor unit, single phase. Monitors for presence of live AC circuit. Accepts inputs from 90 to 240 VAC, single phase source. 0-5 VDC output for direct interface to an MCU digital channel.
AC sensor unit, 3 phase. Monitors for presence of live AC circuit and fault conditions on all phases. Accepts inputs from 90 to 240 VAC. Relay outputs for direct interface to an MCU digital channel or other functions.
COS can supply electronic switches, motor starters and motor controllers for use with the MCU500. Custom solutions are our specialty. Please call for details.
Custom controls: COS makes a variety of custom controls that interface level sensors to motor speed controls for precise level control in tanks. Call us for your application needs
Same as above, but without the GFI: 200-30510-02
3 phase contactor, for motor control. 15 Amp, 240 VAC, with local/off/remote switch. Designed for interface to an MCU digital output channel for direct control of motors, etc..
AC sensor unit, single phase. Monitors for presence of live AC circuit. Accepts inputs from 90 to 240 VAC, single phase source. 0-5 VDC output for direct interface to an MCU digital channel.
AC sensor unit, 3 phase. Monitors for presence of live AC circuit and fault conditions on all phases. Accepts inputs from 90 to 240 VAC. Relay outputs for direct interface to an MCU digital channel or other functions.
COS can supply electronic switches, motor starters and motor controllers for use with the MCU500. Custom solutions are our specialty. Please call for details.
Custom controls: COS makes a variety of custom controls that interface level sensors to motor speed controls for precise level control in tanks. Call us for your application needs
200- 30510-01
200-30510-02
200-30510-03
200-30520
Kits & Accessories
Temp probe cable (6’)
Temp probe cable (10’)
Used to connect temp probes to line amplifiers.
Line amplifier connectors, Hypertronics 6 pin kit COSX1004
Line amplifier connectors, Hypertronics 4 pin kit COSX1003
(Used to connect Line Amplifiers/ Freq. converters to MCU500 cable. Pin
extractors also available. Call for details.)
LEMO 4 pin connector kit, for use with COS Temp probes.
Omega, pH calibration kit, pHA-79. Comes w/ pH 4.0, pH 7.0 and pH10.0 calibration capsules, which, when mixed with distilled water, provide an excellent method of calibrating pH probes and Line amplifiers.
Temp probe cable (10’)
Used to connect temp probes to line amplifiers.
Line amplifier connectors, Hypertronics 6 pin kit COSX1004
Line amplifier connectors, Hypertronics 4 pin kit COSX1003
(Used to connect Line Amplifiers/ Freq. converters to MCU500 cable. Pin
extractors also available. Call for details.)
LEMO 4 pin connector kit, for use with COS Temp probes.
Omega, pH calibration kit, pHA-79. Comes w/ pH 4.0, pH 7.0 and pH10.0 calibration capsules, which, when mixed with distilled water, provide an excellent method of calibrating pH probes and Line amplifiers.
087-40110-01
087-40110-02
COSX1004
COSX1003
COS
200-30520
COSX1002
pHA79